In order to establish proper communication between the display and outdoor transmitter it is important that they be set up as follows:

1. Bring both units inside and have the units 3-5 feet apart with nothing in-between them.
2. Remove the batteries from both units.
3. Press one of the buttons on the display at least 20 times to clear all memory. Verify that the display is blank before proceeding.
4. Using a good quality alkaline battery place them back into the remote sensor; making sure they are installed according to the diagrams in the battery compartment. Next, taking care not to press any buttons, reinstall the batteries in the display according to the diagram in the battery compartment.
5. Do not press any buttons for at least 15 minutes after installing the batteries. (Let them establish a good connection.)
6. An outdoor temperature should be showing on your display. You can now put your outdoor sensor back outside.

In order to get an accurate reading and to prolong the life of your sensor we recommend that you have it in a sheltered area out of the sun and direct rain. Fog and Mist will not affect the sensor, but a soaking in water may. If your sensor becomes soaked, removed the batteries and allow it to try overnight; then restart the station (see section 1A). You can mount it outside under an eve of your house or any other suitable place that will keep it out of the sun and rain. Do not wrap the sensor in plastic or seal it in a plastic bag.

The maximum transmission range is 80 feet in a straight line (line of sight). Exterior walls and obstructions will reduce transmission range by as much as 25-30 feet while interior walls and similar obstructions will reduce transmission range by as much as 15-20 feet. (An obstruction would include anything that is between the line of sight like a roof, walls, floors, ceilings, trees, etc.) For best signal reception the transmission range should be greater than the line of sight distance between the transmitter and receiver. Certain building materials as well as electrical interference may also affect signal reception.

If further assistance is required please contact us via email at support@lacrossetechnology.com or by phone at 1-888-211-1923

The weather station is probably in MIN & MAX mode. Press and release the MIN & MAX button until neither MIN nor MAX is showing on the display.

1. If you have not yet installed the batteries or plugged in the weather station and it shows a time, remove the scratch-guard from the LCD panel.
2. This weather station receives a signal from Ft. Collins, Colorado (WWVB) to set it to atomic time. Sometimes, due to adverse weather or atmospheric conditions you will not be able to receive a signal immediately. The best way to get a signal is to put your weather station in a window facing Colorado until you see the tower icon appear.
3. If your time is off by an increment of 1 hour, change your time zone to match your location.

In order to set up the display, follow these steps:
NOTE: Do not set the time or press any other buttons until the display has communicated with the outdoor transmitter for at least 10 minutes.

1. Press and hold the SET button for 5 seconds. 12h or 24h will appear on the top line (12h for AM/PM, 24h for military time).
   
   To change between 12h and 24h, press and release the MIN & MAX button. When you have your choice shown on the display, press and release the SET button once
   
2. Degree Fahrenheit will now show. To change between Fahrenheit and Celsius, press and release MIN & MAX button. When you have your choice shown on the display, press and release the SET button once.
   
3. Hour will now be flashing. Press and release the MIN & MAX button until correct hour is shown. WATCH the AM/PM. When the correct hours is shown, press and release the SET button once.
   
   NOTE: When in the 12h mode, there is only a "PM" display, which appears under the word TIME. During the "AM" hours, this area will be blank.
   
4. Minute will be flashing. Press and release the MIN & MAX button until the correct minutes are displayed. Press and release the SET button once more and you are done.

Press and hold the MIN & MAX button.

Check the polarity on your batteries to make sure they are installed according to the diagrams in the battery compartment. Also make sure that you are using a new good quality alkaline battery. If the display is still blank after following these steps please contact us via email at support@lacrossetechnology.com or by phone at
1-888-211-1923